Mechanical Properties of Solids Formulas
Every Mechanical Properties of Solids formula for JEE Main & Advanced, NEET, CBSE, with what each symbol means and when it applies.
- Formulas
- 25
- Syllabus
- Class 11 Physics
- For
- JEE & NEET
- Practise
- Chapter PYQs ↗
Mechanical Properties of Solids deals with how solid bodies deform under load and spring back: stress, strain, Hooke's law and the three elastic moduli. Exams mostly ask for the extension of a wire, comparisons between wires of different size or material, elastic energy stored, and reading the stress–strain curve. Keep track of which area and which length each formula uses.
Stress and strain
Stress
SI unit N/m² or pascal. Longitudinal stress acts normal to the area; shearing stress acts along it.
: restoring force (equal to the applied force in equilibrium); : area over which it acts.
Longitudinal strain
Strain is a ratio, so it has no unit.
: change in length; : original length.
Volume strain
Used with the bulk modulus. A decrease in volume makes negative.
: change in volume; : original volume.
Shearing strain
Valid for small angles, which is always the case in the elastic range.
: sideways shift of the top face; : height of the block.
Hooke's law and the stress–strain curve
Hooke's law
Holds only up to the proportional limit, for small deformations.
Points on the stress–strain curve
Beyond the yield point, the body keeps a permanent set when the load is removed. Ductile materials have a long plastic region; brittle ones fracture soon after the elastic limit.
Wire as a spring
Wires joined end to end combine like springs in series.
: force constant of a wire of length , cross-section area , Young's modulus .
Breaking load
Breaking load depends on the area but not on the length of the wire.
: breaking stress, a property of the material alone.
Young's modulus
Young's modulus
A material property: does not depend on the length or thickness of the sample. Steel has a larger than rubber.
Extension of a wire
For the same material and load, .
: diameter of the wire.
Searle's method
The slope of a load–extension graph gives .
: load hung on a wire of radius and length ; : measured extension.
Extension of a wire under its own weightJEE
Half the extension a load equal to the wire's weight would cause, because the average tension is .
: density; : mass of the hanging wire.
Thermal stressJEE
Independent of the length of the rod.
: coefficient of linear expansion; : rise in temperature of a rod clamped between rigid walls.
Bulk modulus and shear modulus
Bulk modulus
The minus sign makes positive, since volume falls as pressure rises. Solids have the largest , gases the smallest.
: increase in pressure.
Compressibility
A large means the material is easy to compress. Gases have the largest compressibility and solids the smallest.
: compressibility, in Pa; : bulk modulus.
Bulk modulus of a gasJEE
Isothermal and adiabatic compression of an ideal gas.
.
Change in density under pressureJEE
Valid when .
Shear modulus (modulus of rigidity)
For most solids is about one third of . Liquids and gases have no shear modulus.
: area of the face parallel to the force.
Poisson's ratio
Poisson's ratio
Dimensionless. Theoretical limits are to ; real materials lie between and .
: lateral strain; : longitudinal strain.
Change in volume of a stretched wireJEE
No volume change when , as for rubber.
Relations between the moduliJEE
For isotropic materials only.
Elastic potential energy and applications
Energy stored in a stretched wire
Half the product of final load and extension, because the force rises from zero.
Energy density
Also equals .
: elastic energy stored per unit volume.
Depression of a beam loaded at the centre
Since , beams are made deep rather than wide; an I-section saves material.
: load at the middle; : span between supports; : breadth; : depth of a rectangular beam.
Maximum height of a mountain
Gives roughly 10 km on the earth, close to the height of the tallest mountains.
: yield stress of the rock; : its density.
Common mistakes
- Using the diameter where the formula needs the radius in , which changes the answer by a factor of 4.
- Thinking Young's modulus depends on the length or thickness of the wire. It depends only on the material.
- Forgetting the factor in elastic energy and writing .
- Thinking rubber is more elastic than steel. Steel has the larger modulus, so it is more elastic in the physics sense.
- Taking the full weight for a wire stretching under its own mass. The average tension is half the weight.
- Dropping the minus sign in the bulk modulus and getting a negative .