Thermal Properties of Matter Formulas
Every Thermal Properties of Matter formula for JEE Main & Advanced, NEET, CBSE, with what each symbol means and when it applies.
- Formulas
- 32
- Syllabus
- Class 11 Physics
- For
- JEE & NEET
- Practise
- Chapter PYQs ↗
Thermal Properties of Matter covers temperature scales, thermal expansion, specific heat and calorimetry, change of state, and the three modes of heat transfer. Exams test mixing problems with latent heat, expansion of rods and liquids, conduction through slabs in series and parallel, Stefan's and Wien's laws, and Newton's law of cooling. Always convert temperatures to kelvin for radiation and gas formulas.
Temperature scales and ideal gas
Converting between temperature scales
A change of C equals a change of 1 K and of F. The two scales read the same at .
General scale conversion
Works for any scale that is linear in temperature: put in the scale's ice and steam readings and solve. The Fahrenheit relation is the case , .
, : readings of any linear scale at the ice point and the steam point.
Ideal gas equation
Combines Boyle's law ( constant at fixed ) and Charles' law ( constant at fixed ).
: number of moles; : absolute temperature in kelvin.
Constant-volume gas thermometerJEE
Readings agree for all gases only in the limit of low pressure, where every gas behaves ideally.
K: triple point of water; : gas pressure at the triple point.
Thermal expansion
Linear, area and volume expansion
Valid for small , treating the coefficients as constant. A hole or cavity expands as if it were filled with the material.
, , : coefficients of linear, area and volume expansion.
Relation between expansion coefficients
For an isotropic solid.
Volume expansion of an ideal gas
At constant pressure. At C this is about per K, much larger than for solids or liquids.
Change in density with temperatureJEE
Mass stays the same while volume grows, so density falls. Valid for small ; water between C and C is an exception.
Apparent expansion of a liquidJEE
The vessel expands too, so the liquid level rises by less than the real expansion.
Pendulum clock and temperatureJEE
A clock with a metal pendulum runs slow in summer.
: time period; : rise in temperature.
Bimetallic stripJEE
Bends with the higher- metal on the outside.
: radius of curvature; : thickness of each strip.
Anomalous expansion of water
Between C and C water contracts on heating. Lakes freeze from the top, so water below stays liquid.
Specific heat and calorimetry
Heat and specific heat capacity
Water has J kg K, one of the highest of common substances.
: specific heat capacity, J kg K; : heat capacity of the body.
Molar specific heat
The second relation holds for an ideal gas. For solids and liquids, and are nearly equal.
Principle of calorimetry
Valid when no heat escapes to the surroundings. Include the calorimeter's own heat capacity.
Final temperature of a mixtureJEE
Only when neither substance changes state. Otherwise check first whether all the ice melts.
Water equivalentJEE
Lets you treat a vessel as an extra mass of water in calorimetry sums. Its unit is kg, though it stands for a heat capacity.
: mass of water with the same heat capacity as the body.
Change of state and latent heat
Latent heat
Temperature stays constant during the change. For water, J/kg and J/kg.
: specific latent heat for melting () or boiling ().
Heat to turn ice into steam
Specific heat of ice is about half that of water.
: rise from the ice's starting temperature to C; : rise of the steam above C.
Triple point and pressure effects
Raising pressure raises the boiling point and lowers the melting point of ice (regelation).
Conduction
Rate of heat conduction
Steady state only: temperature at each point no longer changes.
: thermal conductivity; : cross-section area; : length; .
Thermal resistanceJEE
Same form as Ohm's law, with heat current for electric current and temperature difference for voltage.
Slabs in series and parallelJEE
In series, the same heat current flows through each slab.
Equivalent conductivityJEE
For equal lengths in series, .
: two slabs of equal area joined in series; : two rods of equal length side by side.
Junction temperature of two slabsJEE
Follows from equal heat current through both slabs in the steady state. The junction temperature is closer to the outer temperature of the slab with larger .
Equal areas; outer faces held at and .
Growth of ice on a pondJEE Advanced
The time grows as the square of the thickness, so ice twice as thick takes four times as long to form from zero. The water just below the ice stays at C.
: degrees below C of the air; : conductivity of ice; , : initial and final thickness.
Convection, radiation and cooling
Stefan–Boltzmann law
Net loss to surroundings at is .
: emissivity ( for a perfect black body); : absolute temperature.
Wien's displacement law
Hotter bodies peak at shorter wavelengths: a heated iron turns from red to yellow to white.
: wavelength at which a black body emits most strongly.
Kirchhoff's law of radiationJEE
Good absorbers are good emitters.
: emissive power; : absorptivity at wavelength and the same temperature.
Newton's law of cooling
Holds when the temperature difference is small, a few tens of kelvin at most.
: temperature of the surroundings; : constant for the body and surface.
Average form of Newton's law of cooling
Quick approximation used in most numericals.
, : temperatures at the start and end of time .
Solar constant and temperature of the SunJEE
Treats the Sun as a black body. With kW/m² at the earth, it gives a surface temperature of about 5800 K.
: power received per unit area at distance ; : radius of the Sun.
Common mistakes
- Using Celsius instead of kelvin in Stefan's law or Wien's law. Both need absolute temperature.
- Assuming all the ice melts in a mixing problem. First check whether the heat available can melt it; if not, the final temperature is C.
- Using or ; the correct relations are and .
- Thinking a hole in a heated plate shrinks. It expands as if made of the plate material.
- Applying Newton's law of cooling to large temperature differences, where Stefan's law is needed.
- Adding thermal conductivities for slabs in series. Add thermal resistances instead.